Need help?


Search OutdoorKing-Forum by entering Key Words Below



Who's Online Now
0 members (), 8,922 guests, and 1,683 robots.
Key: Admin, Global Mod, Mod
Newest Topics
Villiers Mk2 Midget needs to be serviced
by Szymon - 16/11/26 03:58 PM
Choosing a blower
by Dandare - 15/11/26 02:15 PM
Scott Bonnar 33 Verticutter
by Malcolm Arnold - 14/11/26 10:52 AM
southern cross KX-C for sale?
by Olqualcast - 12/11/26 02:49 PM
Scott Bonnar 45 ID help
by jimmywa - 07/11/26 06:48 PM
Rover 45 Catcher
by Rover45Restoration - 03/11/26 04:38 PM
Topic Replies
Villiers Mk2 Midget needs to be serviced
by Bruce - 16/11/26 09:36 PM
Choosing a blower
by MowingManiac - 16/11/26 07:14 AM
Scott Bonnar 33 Verticutter
by Malcolm Arnold - 14/11/26 10:52 AM
southern cross KX-C for sale?
by Olqualcast - 12/11/26 02:49 PM
Morrison olympic 600 backlap tips
by midget98 - 12/11/26 01:51 AM
Scott Bonnar 45 ID help
by jimmywa - 08/11/26 12:00 AM
Victa Runs Then Starts To Stall
by Man With Cheese - 07/11/26 11:33 PM
Rover 45 Catcher
by looktall - 03/11/26 07:47 PM
Ryobi RST131ES: fuel tank
by Bruce - 03/11/26 02:14 PM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
Joined: Dec 2016
Posts: 1
Novice
Hi all! Just replaced an old tecumseh with a briggs into a greenfield fastcut.

Everything seemed to run smoothly...I took a punt and simply plugged the new briggs 19hp pro into the previous wire plug which was a tecumseh 13hp. (same plug and wires seemed to line up in the plug) started first go, seemed ok. but did not idle after a few goes but starts fine. dripped petrol (gas) into the air filter and it ran whilst doing this whilst at low revs. but when I went to see if it would run at full throttle it cut out and good amount of smoke came out.

has anyone got any tips?
I probably should re-wire properly, but it could run without changing anything (not idle)

Last edited by CyberJack; 01/01/17 12:39 AM. Reason: Topic Heading.
Joined: Jan 2016
Posts: 8,216
Likes: 235
SENIOR TECHNICIAN
I haven't had anything to do with those big motors but just taking a stab, is the motor you have just fitted new or second hand? I assume these run magneto so that really only leaves the carby as the problem. As for the plug and re-wiring, seems like it is working, all you then have to prove is that it is charging the battery, put a volt meter on that and you will know straight away

Joined: Oct 2014
Posts: 4
Novice
Has the Briggs got a fuel cut solenoid that screws into the bottom of the carby. If it has then check you are getting power to it and that it is working.

Joined: Jun 2013
Posts: 407
Likes: 2
LRT Offline
Qualified Junior
As Fixdit said, depending on how old the engine is of course, it should have the solenoid on the bottom of the carby. The solenoid's purpose is to prevent the engine 'running on' after the ignition is turned off.

As Norm also said, the ignition shouldn't be the cause as it uses a magneto.

See the excerpt from the B&S workshop manual below:

Testing Fuel Shut Off Solenoid
The fuel shut off solenoid is controlled by the
equipment ignition switch. With the switch OFF,
the solenoid plunger closes, stopping the fuel
flow at the fixed main jet. With the switch in the
ON and START positions, the solenoid plunger
opens, allowing normal fuel flow. If operating
properly, the solenoid will click when the switch
is turned ON and OFF.

If convenient, can you post the engine model, type, & code? It should be etched onto the top of the rocker cover.

The red arrow in the picture below is pointing to the solenoid.
[Linked Image]


Moderated by  bigted, Bruce, CyberJack, Gadge, Mr Davis 

Link Copied to Clipboard
November
M T W T F S S
1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30
Newest Members
AndrewD, Telly, Szymon, BEVERLEY, foxbeans
18,229 Registered Users
Forum Statistics
Forums144
Topics12,777
Posts106,880
Members18,230
Most Online40,124
Apr 13th, 2026
OutdoorKing Showcase
20 Bucks from FB Marketplace
20 Bucks from FB Marketplace
by Return Rider, February 20
Victa Cortina 2 Shed Find
Victa Cortina 2 Shed Find
by Return Rider, January 25
My Rover Baron 45
My Rover Baron 45
by Maxwell_Rover_Baron, April 16
SHOWCASE - Precision Mowers - 2021
SHOWCASE - Precision Mowers - 2021
by CyberJack, April 14
SHOWCASE – Atco Rotary – Paul C - 2020
SHOWCASE – Atco Rotary – Paul C - 2020
by CyberJack, December 28
HOME |CONTACT US
Powered by UBB.threads™ PHP Forum Software 8.0.1