OutdoorKing Repair Forum Forums Finding and Swapping Rare Finds & Donations VC-125 MKII Bitsa.

Don't know didn't watch that one,and I properly won't.You should watch it funny Wayne's world 2 that was in.Anyway back to topic.If anybody has a base to suit just let me know.I may put it in the wanted section as well.

we find out in @ 5 hours hahaha . then i bet both 160's too , but bits will be handy i guess

...and that's why I haven't put it in the wanted section yet.

So did we win?

sure did , just sorting out a time i'll call him tomorrow n sort it . got a few other things too i probably dont need ! so allgood pic's when i get 'em here geeeez i hope at least one is correct

Well I guess if they are both VC-125's with 160cc engines then maybe not.Unless the other one that wasn't pictured just has the wrong cowl.I know that the one in the picture was a VC-125 with a 160cc so that one isn't correct.

they do both look the same , are they a tad smaller than a 160 base ? something makes 'em look it so here ya go , hope theare what you need

the parts one

the one from the pic' you did see before

and these i think i needed anyway hope its the right one ! and sorry about the pic's . flash didt wanna work on camera

Have you got them already? Wow.Take some pictures side on,it's a bit hard to tell what they are from that angle.

try again , oops




hope these help ? or maybe in the daylight , they werent too far from here and i felt like a drive those auto drive type wheels agian with no drive teeth on one of 'em , and yes the rear wheels do look too big i think

The one closest has the 8" wheels the furtherst one looks like its got 7" wheels.


Those autodrives with no teeth, I had them on something here a while back. MrDavis was going to try and sort out the what and the why with that one.
Personally I think they fit in somewhere between the large centre cap moulded/solid rubber and the moulded plastic treaded wheels.

The moulded rubber large cap wheels is what that should have on it. Front and back.

i think they both have the wrong wheels ? one has something like it should have and still to dark to go n look at the right ones . its only a base needed so if both 160's i need one to finish another the handle holes are flogged out badly , i remember something about ty sorting where those wheels fit into the picture yeh

Have you been using your phone again to take pictures? I can't quite tell if it is what I'm after or not.I'd say the one with the auto drive non teeth one won't be the right one.Don't suppose you could do some clearer pictures?

phew ! haha i'll try in a min' . gotta get the daughter to turn on the flash new fangle gadgets drivin' me nuts




there ya go , did it mysekf too never too old huh hope these are better ? next best thing i can do is put a real 160 beside it n take more , got a couple here . for some reason they look smaller

Is the one with the Auto Drive no teeth wheels hitting the base anywhere?Also does ether one have green paint on the handles?As I'm thinking they just be VC-160 bases.

its damn close !!! both have plastic hieght adjusters too , i just notice one of my 160's has a metal one , both have differnt size rear wheels too (on 160's) . i think if it was used it would rub on the base

There maybe another way to tell.Only thing is the engine needs to come off the base and under the engine near where it bolts on there is a number cast into the base.Now I can't remember what the VC-125 Mark I had but the Mark II has a 4 cast into it.If it's a 1 I believe it would be a VC-160 Mark II.I don't know what these numbers stand for,but from what I have seen they are slightly different from each other.Don't know why or what it means.

no worries , i dont need this many in one piece haha gimme a little time n i'll pull them down n see and compare with what i have , as mine dont look too modified or changed in most ways , but where does the metal hieght adjuster come in ? both look the same now i'm getting confused

Not sure throw a picture up. VC-160 have the height adjusters you have on those two.

i'll do it tomorrow night mate , they are up on a shelf ! and i never noticed before they were different , both the "125's" have plastic , one of my 160's is plastic too , the other metal riveted to the base

OK that sounds different.I'll wait and see the pictures hoping I can help you with that.