Need help?


Search OutdoorKing-Forum by entering Key Words Below



Who's Online Now
1 members (Dandare), 1,917 guests, and 2,283 robots.
Key: Admin, Global Mod, Mod
Newest Topics
Ratchet washer
by FiM - 12/09/26 02:12 PM
Help to identify this Qualcast
by Olqualcast - 11/09/26 10:55 PM
Help identify walk-behind slasher
by mower1 - 05/09/26 05:51 PM
Free to good home – 1955 Villiers reel mower
by Cylon - 27/08/26 01:04 PM
Info on Pope Rotary Valve 2T Single Cylinder Engines
by BeardedBiker55 - 18/08/26 04:21 PM
Briggs primer bulb
by NormK - 25/07/26 03:58 PM
Topic Replies
Ratchet washer
by NormK - 12/09/26 07:48 PM
Help to identify this Qualcast
by maxwestern - 12/09/26 06:09 PM
Victa 2-Stroke: Looks Like the End
by NormK - 09/09/26 05:07 PM
Help identify walk-behind slasher
by maxwestern - 07/09/26 10:20 PM
Free to good home – 1955 Villiers reel mower
by Cylon - 27/08/26 01:04 PM
Villiers marvil
by Steve Mack - 26/08/26 06:46 PM
Info on Pope Rotary Valve 2T Single Cylinder Engines
by BeardedBiker55 - 20/08/26 03:37 PM
Briggs primer bulb
by Oldeyes - 17/08/26 05:53 PM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
Joined: May 2011
Posts: 3
Novice
Hi all

I currently mow with a Scott Bonnar 45 20" cut, but I have just stumbled across a Scott Bonnar Queens 24" that I have gotten my hands on.

It looks like it has the original Villiers engine (Mark 25RG). I am unable to start the engine as the ignition wire has been ripped from the coil.

The engine looks rough with a home made muffler and air filter. I have been told that it was running prior to the ignition lead being ripped off and the mower being put into storage (7 years ago). Motor turns over ok using the crank lever.

The rest of the mower is in overall good condition and will come up well with some cleaning and servicing.

My dilemma - how hard is it to find parts for this engine? Is it worth fixing (will be a process of elimination). I have had no luck searching so far for an ignition lead/coil

If I was to replace the engine, what should it be? ie B&S 5hp?

Thanks
Andrew

Joined: Jan 2015
Posts: 988
Likes: 7
Qualified Senior
Hi Andrew,

Can you post a pic of the engine please, if you are able. Use the photo attatch down the bottom of the post.

All the best
Paul

Joined: May 2011
Posts: 99
Likes: 1
Atco Specialist
Hi Andrew,

Many post war Villiers engines had separate HT leads that screwed into the magneto backing plate with a bakelite fitting. The connection between lead and coil was via a spring loaded contact. If the bakelite fitting is still in place, unscrew it and see if the spring and contact are still there. If so it may just be case of attaching a length of new HT lead (there will be a little screw that connects the contact to the wire). If not, the lead with fittings can be obtained via a number of suppliers there is atlas one in Aus but there are a number in England.

If it is a C25 engine, then it will have a different arrangement where the HT cable is cast into the coil assembly. Again, parts can be obtained from the same sources.

Overall, these engines are fairly strong and are reasonably straight forward to work on.

Kind regards,

Sir Chook


Moderated by  Bruce, CyberJack, Mr Davis 

Link Copied to Clipboard
September
M T W T F S S
1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30
Newest Members
alwayscreaming, FiM, gussie_24, F1145, flcn67
18,109 Registered Users
Forum Statistics
Forums144
Topics12,753
Posts106,792
Members18,110
Most Online40,124
Apr 13th, 2026
OutdoorKing Showcase
20 Bucks from FB Marketplace
20 Bucks from FB Marketplace
by Return Rider, February 20
Victa Cortina 2 Shed Find
Victa Cortina 2 Shed Find
by Return Rider, January 25
My Rover Baron 45
My Rover Baron 45
by Maxwell_Rover_Baron, April 16
SHOWCASE - Precision Mowers - 2021
SHOWCASE - Precision Mowers - 2021
by CyberJack, April 14
SHOWCASE – Atco Rotary – Paul C - 2020
SHOWCASE – Atco Rotary – Paul C - 2020
by CyberJack, December 28
HOME |CONTACT US
Powered by UBB.threads™ PHP Forum Software 8.0.1