Need help?


Search OutdoorKing-Forum by entering Key Words Below



Who's Online Now
2 members (nath, Ashgren), 8,097 guests, and 1,814 robots.
Key: Admin, Global Mod, Mod
Newest Topics
Villiers Mk2 Midget needs to be serviced
by Szymon - 16/11/26 03:58 PM
Choosing a blower
by Dandare - 15/11/26 02:15 PM
Scott Bonnar 33 Verticutter
by Malcolm Arnold - 14/11/26 10:52 AM
southern cross KX-C for sale?
by Olqualcast - 12/11/26 02:49 PM
Scott Bonnar 45 ID help
by jimmywa - 07/11/26 06:48 PM
Rover 45 Catcher
by Rover45Restoration - 03/11/26 04:38 PM
Topic Replies
Villiers Mk2 Midget needs to be serviced
by Bruce - 16/11/26 09:36 PM
Choosing a blower
by MowingManiac - 16/11/26 07:14 AM
Scott Bonnar 33 Verticutter
by Malcolm Arnold - 14/11/26 10:52 AM
southern cross KX-C for sale?
by Olqualcast - 12/11/26 02:49 PM
Morrison olympic 600 backlap tips
by midget98 - 12/11/26 01:51 AM
Scott Bonnar 45 ID help
by jimmywa - 08/11/26 12:00 AM
Victa Runs Then Starts To Stall
by Man With Cheese - 07/11/26 11:33 PM
Rover 45 Catcher
by looktall - 03/11/26 07:47 PM
Ryobi RST131ES: fuel tank
by Bruce - 03/11/26 02:14 PM
Previous Thread
Next Thread
Print Thread
Rate Thread
Hop To
Joined: May 2020
Posts: 25
Likes: 2
tobyoats
Fitting my red Kirby 4 stroke engine to my restored SB33 0919 (flat bar handles).

I find that the engine output shaft contacts (end to end) to the clutch shaft inside the friction clutch housing. This stops the engine sliding over the engine securing bolt holes (4) on the solid base plate by approx 10mm.

Any ideas why this is happening and what solutions are out there. The clutch lever is not engaged, I could shorten up the engine output shaft if the problem is caused by mix matched parts.
(I have sourced parts from two SB33 wrecks, so the restoration is a mix match of parts.)

Malcolm.

Portal Box 6
Joined: Jan 2015
Posts: 1,548
Likes: 25
AVB Offline
SENIOR TECHNICIAN
If this is anything like log splitter setups here with horizontal engine where the new engine pto shaft is long it is a simple matter to just shorten the PTO . Just got it is done squarely. Here several jobs required shorten the shafts by 3/4 of an inch so the Love Joy coupler could fit inside the housing that coupled the hydraulic pump.

Now of course I have never seen a SB33 mower so others here that is more familiar with the setup might know better.

Joined: Jan 2016
Posts: 8,216
Likes: 235
SENIOR TECHNICIAN
1mm grinder disc will cut it back in quick time

Joined: May 2020
Posts: 25
Likes: 2
tobyoats
Thanks for the replies. I have fixed the problem without the need to cut down the output shaft of the engine.

I checked out a spare clutch shaft (from my spare parts) and found that it is 10mm shorter than the one that I used, I swapped them over and I now have an operating clutch.

Another example of where asking questions on a forum like this one creates information and allows you to search for answers and learn more about a subject.
Thanks

Malcolm.

Joined: Jan 2015
Posts: 1,548
Likes: 25
AVB Offline
SENIOR TECHNICIAN
Sometimes that our discussions do get member to go through their minds cobwebs. I had similar experiences when asking questions to only have come to light from the cobwebs of my mind.


Moderated by  Bruce, CyberJack 

Link Copied to Clipboard
November
M T W T F S S
1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30
Newest Members
AndrewD, Telly, Szymon, BEVERLEY, foxbeans
18,229 Registered Users
Forum Statistics
Forums144
Topics12,777
Posts106,880
Members18,230
Most Online40,124
Apr 13th, 2026
OutdoorKing Showcase
20 Bucks from FB Marketplace
20 Bucks from FB Marketplace
by Return Rider, February 20
Victa Cortina 2 Shed Find
Victa Cortina 2 Shed Find
by Return Rider, January 25
My Rover Baron 45
My Rover Baron 45
by Maxwell_Rover_Baron, April 16
SHOWCASE - Precision Mowers - 2021
SHOWCASE - Precision Mowers - 2021
by CyberJack, April 14
SHOWCASE – Atco Rotary – Paul C - 2020
SHOWCASE – Atco Rotary – Paul C - 2020
by CyberJack, December 28
HOME |CONTACT US
Powered by UBB.threads™ PHP Forum Software 8.0.1