Recent Topics: All allowed forums https://outdoorking-forum.com.au/forum/ubbthreads.php?ubb=cfrm Taken from all forums en-us Mon, 09 Nov 2026 18:03:54 UTC 5 support@outdoorking-forum.com.au (OutdoorKing Repair Forum) UBB.threads https://outdoorking-forum.com.au/forum/images/general/default/rss_icon.gif Recent Topics: All allowed forums https://outdoorking-forum.com.au/forum/ubbthreads.php?ubb=cfrm Pressure washer engine's Honda GX390 remove gum from carburetor's internal https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122587.html#Post122587
Quote
Brake cleaner is similar to carb cleaner but uses slightly different chemicals.It works well enough that I'll use it for carbs if I don't have carb cleaner and I use it as a good general parts cleaner.
Noted

Quote
You should really remove orings and other seals when cleaning a carb.
Carb cleaner and brake cleaner can both cause damage to them although some cleaners are less aggressive and can be less likely to damage them.
And ultrasonic cleaners can also cause damage to orings either through swelling or straight up disintegration of old worn seals.
Will consider that

Quote
Sometimes there's a bit of trial and error to find a good cleaner that doesn't damage plastics and rubber.
Agree

Regards

]]> Sun, 08 Nov 2026 00:48:28 +0000 zillh2004 https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122587.html#Post122587 Scott Bonnar 45 ID help https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122582.html#Post122582
The handlebars are a shame, and squished how they are I don’t think are repairable, so I’m searching for some.

]]> Sat, 07 Nov 2026 13:00:07 +0000 jimmywa https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122582.html#Post122582 Rover 45 Catcher https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122578.html#Post122578
]]> Tue, 03 Nov 2026 08:47:12 +0000 looktall https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122578.html#Post122578 Victa Runs Then Starts To Stall https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122581.html#Post122581
When I reassembled the carb I set the poppet valve to the 'A' setting. I mowed for about 15 minutes on full throttle before the same problem of it starting the stall. I left it for the day then set the poppet valve to the 'C' setting.
Mowed with a full fuel tank on full throttle with no stalling. Re-fueled and mowed for another 15 minutes (I live on a large corner block) with full throttle.

I can't recall what the setting was before but would have been the 'A' setting as I recall the revs were lower than the 'C' setting. One thing I did notice is on the 'A' setting when it was idling the revs were very low but doesn't explain why it would suddenly start to stall after a while on full throttle when it was fine before. Anyway I may experiment with another poppet valve and see what happens.

Thanks for your replies.

]]> Sat, 07 Nov 2026 12:33:57 +0000 Man With Cheese https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122581.html#Post122581 Ryobi RST131ES: fuel tank https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122576.html#Post122576
Originally Posted by barramundi2
Thanks Bruce - the info on the line is good news. An Exploded View of Parts into AI Claude has come up with a method to remove tank, but looks complicate No scrwews on tank, but need to remove a lot of gear just to get at tank. Cheers. Thanks

If you have taken the air filter cover of it is easy to remove the tank only 4 screws to undo to get it off.

]]> Tue, 03 Nov 2026 03:14:50 +0000 Bruce https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122576.html#Post122576 Morrison olympic 600 backlap tips https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122555.html#Post122555
You could try typing back laping in the search bar at the top of the forum and you will see a lot of topics regarding the issue rather than try to look through the forums.

What we used in the past (many years ago) was use a retangle block of steel and drill holes in it and place a bolt in the centre with nut either side to lock it and then drill two other holes so that a bolt will fit into each side of the sprocket. Not hard to make no welding etc.

Hope that this is of some help to you.

]]> Fri, 30 Oct 2026 08:12:18 +0000 Bruce https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122555.html#Post122555 Scott Bonnar 45 https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122561.html#Post122561 https://mowpartsoz.com.au/collectio...clutch-cotter-pin?variant=38511663218839

So somewhere out there is a 3/4" clutch half that uses a cotter pin. Whether it's factory or aftermarket, who knows.

]]> Sat, 31 Oct 2026 00:12:42 +0000 looktall https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122561.html#Post122561 Victa Trimmer Head/Spool question https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122562.html#Post122562
]]> Sat, 31 Oct 2026 10:39:24 +0000 MowingManiac https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122562.html#Post122562 Victa Cutting Disc Washer https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122567.html#Post122567
]]> Mon, 02 Nov 2026 08:32:35 +0000 Weka https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122567.html#Post122567 Cox 09J6 Compact Tractor — Steering Linkage Question https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122560.html#Post122560
Sorry for the late reply regarding your issue.

If you type in Cox 09J6 into the search box on the forum you will get quite a few post come up regarding that model including parts list etc which should assis you in fixing you problem.

Here is a link to one post that has quite a bit of information.CLICK HERE

]]> Fri, 30 Oct 2026 22:53:42 +0000 Bruce https://outdoorking-forum.com.au/forum/ubbthreads.php/topics/122560.html#Post122560